Showing results: 121 - 135 of 1138 items found.
-
Au Group Electronics
The Au Truck / Bus Fleet Management System (FMS) simulator can generate Controller Area Network (CAN) signal per Truck FMS Standard (Vers. 02.00) and Bus FMS Standard (Vers. 00.02). Au FMS simulators are designed very easy to use. All editions can run independently (without personal computer). Au FMS Simulators are widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration, to product development and product validation.
-
ELAn-4a -
MRC ltd.
A super wide uniform temperature zone (90mm)ensures complete combustion of coal samples.Dilated and thickened platimum electrode plates with bigger interface, make the interation more accurate and complete. With CAN bus, several sulfur analyzers can be controlled by a single PC, balances could be connected and data could be transmitted by real-time network transmission.
-
781962-01 -
NI
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
YAVHF3X4C50 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4C -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
CSM Products, Inc.
For high-speed measurement applications exceeding the CAN bus capabilities, CSM's EtherCAT®-based MiniModules provide the optimal solution. EtherCAT® is an established protocol for fast and synchronous measurements with its roots in the test bench measurement technology sector. It has high bandwidth capability, maximum number of measurement channels, and precise synchronization of measurement signals.
-
CAEN S.p.A.
CAEN has decades of expertise in design and production of VME and NIM powered crates. The full line of crates is intended to guarantee reliability and mechanical solidity. CAN offers a selection of NIM, VME and Mixed Powered Crates with different configuration of power supplies and backplanes. Some crates can be ventilated with pluggable fan units, which also allow to have additional interfaces for remote monitoring and setting via CAN bus, Ethernet, USB and RS232.
-
781639-01 -
NI
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
AS519 -
6TL Engineering
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
Excalibur Systems, Inc.
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
784121-01 -
NI
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
785324-01 -
NI
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
785325-01 -
NI
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
784122-01 -
NI
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
